CE marking rules and CE marking dimensions are not left to the manufacturer’s discretion: the form of the marking, its minimum height, and where, when and by whom it is affixed are all laid down in legislation. In the EU, these rules are set out in Article 30 and Annex II of Regulation (EC) No 765/2008 and in Decision No 768/2008/EC; in Türkiye, they are set out in the “CE” Marking Regulation published in Official Gazette No 31493 of 27 May 2021.
This article brings together the general rules, the proportions derived from the scale drawing, and the additional requirements of the machinery, noise and EMC legislation, and answers the question “How is the CE marking affixed?” step by step. With the CE marking size calculator and generator in this article, you can calculate your own dimensions and download the marking as SVG, DXF or PNG.
- Unless the applicable legislation specifies a different size, the marking must be at least 5 mm high.
- It may be reduced or enlarged, but the proportions of the scale drawing must be respected.
- It is affixed to the product itself or to its data plate so that it is visible, legible and indelible.
- It is affixed before the product is placed on the market, and only by the manufacturer or its authorised representative.
- Where the applicable legislation so requires, the marking is followed by the identification number of the notified body.
Contents
Which Legislation Sets Out the CE Marking Rules?
The general framework for the CE marking rules is set by horizontal legislation; product-specific directives and regulations may add further requirements. Before affixing the marking, you should therefore check all of the CE marking regulations and directives that apply to the product.
| Legislation | Relevant provision | What it covers |
|---|---|---|
| Regulation (EC) No 765/2008 | Article 30, Annex II | General principles, form and minimum height of the CE marking |
| Decision No 768/2008/EC | Annex I, Articles R11 and R12 | Rules and conditions for affixing the marking (reference provisions used as the basis for product legislation) |
| “CE” Marking Regulation of Türkiye (Official Gazette 27.05.2021 / 31493) | Article 10, Annex 1 | Affixing and use of the marking in Türkiye |
| Machinery Directive 2006/42/EC | Article 16, Annex III; Annex I, section 1.7.3 | Machinery-specific rules on size, location and identification number |
| Outdoor Noise Directive 2000/14/EC | Article 11, Annex IV | CE marking and indication of the guaranteed sound power level |
| EMC Directive 2014/30/EU | Articles 16 and 17 | Affixing the marking to the apparatus or to its data plate |
| Machinery Regulation (EU) 2023/1230 | Articles 23 and 24 | Machinery and related products from 20 January 2027 |
Article numbers refer to the EU legislation; article numbers in the harmonised Turkish regulations may differ.
CE Marking Dimensions
The form of the CE marking is given in Annex II of Regulation (EC) No 765/2008, and in Annex 1 of the Turkish “CE” Marking Regulation, as a graduated (grid) drawing. There are three basic rules for CE marking dimensions:
- Form: The marking consists of the initials “CE” in the form shown in the drawing; the design may not be altered.
- Proportions: The marking may be reduced or enlarged, but the proportions given in the drawing must be respected.
- Minimum size: Unless the applicable legislation specifies a different size, the marking must be at least 5 mm high. The legislation sets no upper limit.
How to Read the Scale Drawing
CE marking dimensions are read from the grid units of the drawing:

- Each letter is derived from a circle with an outer radius of 10 units; the letter height is 20 units.
- The stroke thickness is 3 units (inner radius 7 units).
- The distance between the centres of the two circles is 17 units; the outer circle of the “C” is tangent to the inner circle of the “E”.
- The middle arm of the “E” is 2 units shorter than the upper and lower arms.
- The total width of the marking is 28 units; in other words, the width is 1.4 times the height.
These values are not written as numbers in the legislation; they are read from the grid of the scale drawing. In practice, the marking should not be redrawn by hand but scaled without distorting its proportions; the European Commission publishes vector files of the marking on its CE marking page.
CE Marking Size by Height
The diagram below shows the CE marking dimensions for the minimum height of 5 mm; the table gives the dimensions for larger sizes.

| Letter height | Total width | Stroke thickness | Distance between centres |
|---|---|---|---|
| 5 mm (minimum) | 7 mm | 0.75 mm | 4.25 mm |
| 10 mm | 14 mm | 1.5 mm | 8.5 mm |
| 15 mm | 21 mm | 2.25 mm | 12.75 mm |
| 20 mm | 28 mm | 3 mm | 17 mm |
| 40 mm | 56 mm | 6 mm | 34 mm |
The CE marking dimensions in the table are calculated from the proportions of the scale drawing (1 unit = letter height / 20).
CE Marking Size Calculator and Generator
Enter the height (A) or the total width (B) in millimetres. The tool calculates the CE marking dimensions using the letter codes in the diagram and provides the marking at the exact size you entered as a vector (SVG, DXF) or print-ready (PNG) file. The grid unit is derived from the value entered (1 unit = A ÷ 20 or B ÷ 28), and each dimension is obtained by multiplying the unit by the grid count of that dimension. If a notified body identification number is required, the tool adds 2908 in proportion to the CE marking; when the number is required is explained in the section below.

The identification number follows the CE marking where the applicable legislation so provides and the notified body was involved in that procedure: under 2006/42/EC, only in full quality assurance; under (EU) 2023/1230 (from 20 January 2027), in EU type-examination + Module C, Module H and Module G. Under 2006/42/EC, no number is affixed for EC type-examination; 2014/30/EU (EMC) and 2000/14/EC (noise) do not provide for an identification number.
| Code | Dimension | Grid count | Result |
|---|---|---|---|
| A | Height | 20 | 10 mm |
| B | Total width | 28 | 14 mm |
| C | Stroke thickness | 3 | 1.5 mm |
| D | Letter width (same for “C” and “E”) | 11 | 5.5 mm |
| E | Gap between the two letters | 6 | 3 mm |
| F | Distance between the circle centres | 17 | 8.5 mm |
| G | Outer radius | 10 | 5 mm |
| H | Inner radius | 7 | 3.5 mm |
| J | From the left edge of the “E” to the tip of the middle arm | 9 | 4.5 mm |
| Format | Suitable for | Size information |
|---|---|---|
| SVG | Label and data plate design, printing, graphics software | Width and height are stored in the file in mm |
| DXF | CAD drawings, laser marking and engraving | Drawing unit is mm; consists of arcs and line segments |
| PNG | Word, Excel and label printer software | The selected dpi is written to the file; transparent background |
For information purposes only. Results are rounded to a maximum of three decimal places. The CE marking may be affixed only to products for which the applicable legislation provides for it and whose conformity assessment has been completed, and only by the manufacturer or its authorised representative. The grid counts are taken from the scale drawing in Annex II of Regulation (EC) No 765/2008; the applicable product legislation may specify a different minimum size. Check the dimensions before using the file for printing or engraving.
Colour and Form
The legislation does not prescribe a specific colour for the CE marking. According to the European Commission’s Blue Guide (2022/C 247/01), the marking may take different forms (for example a different colour, solid or hollow) as long as it remains visible and legible and its proportions are respected.
Can the CE Marking Be Smaller Than 5 mm?
The 5 mm rule applies unless the applicable legislation provides otherwise. For example, Annex III of 2006/42/EC states that the minimum dimension may be waived for small-scale machinery. Where the nature of the product does not allow the marking to be affixed visibly, legibly and indelibly, it is affixed to the packaging and to the accompanying documents.
Where Is the CE Marking Affixed?

On the Product or Its Data Plate
The basic rule is that the marking is affixed to the product itself or to its data plate. Where that is not possible or not warranted on account of the nature of the product, the marking is affixed to the packaging and to the accompanying documents required by the applicable legislation. According to the Blue Guide, the marking may not be moved from the product to the packaging or documents for purely aesthetic reasons.
Visible, Legible and Indelible
The Blue Guide explains these three conditions as follows:
- Visible: The marking must be easily accessible to all parties; it may also be placed on the back or underside of the product.
- Legible: The minimum height of 5 mm is required to ensure that the marking is legible.
- Indelible: Under normal circumstances, the marking cannot be removed without leaving noticeable traces. This does not mean that it must form an integral part of the product.
When and by Whom?
The CE marking is affixed before the product is placed on the market (for machinery, before it is placed on the market or put into service). It is affixed once conformity assessment has been completed under all legislation applicable to the product; the manufacturer also draws up the EU declaration of conformity.
The marking may be affixed only by the manufacturer or its authorised representative; the authorised representative is a person mandated in writing by the manufacturer to carry out specified tasks. By affixing the marking, the manufacturer declares that it takes responsibility for the conformity of the product with the applicable legislation. Importers and distributors who place a product on the market under their own name or trademark, or who modify a product already on the market in a way that may affect its conformity, are also considered manufacturers (Turkish “CE” Marking Regulation, Article 9).
Use Alongside Other Markings
- The CE marking is affixed only to products for which the applicable legislation provides for it; it may not be affixed to any other product.
- Markings, signs and inscriptions that are likely to mislead third parties as to the meaning or form of the CE marking may not be affixed to the product.
- Other markings may be used provided that the visibility, legibility and meaning of the CE marking are not impaired.
- The marking may be accompanied by a pictogram indicating a specific risk or use.
- Where a product is subject to more than one piece of legislation, the CE marking indicates conformity with all of the legislation applied.
How to Affix the CE Marking: Step by Step
In practice, the CE marking rules are followed in this order:
- Identify the legislation: Determine all directives and regulations that apply to the product and provide for CE marking.
- Conformity assessment: Complete the applicable procedure, with the involvement of a notified body where required; compile the technical file and draw up the EU declaration of conformity.
- Use the correct drawing: Take the marking from a vector file that matches the scale drawing and scale it without distorting the proportions.
- Choose the size: Set the CE marking height to at least 5 mm, and check whether the product legislation has a specific size requirement.
- Choose the location: Place the marking where it is easily seen on the product itself or on its data plate; on machinery, in the immediate vicinity of the manufacturer’s name.
- Apply it with a permanent method: Apply the marking so that it cannot be removed under normal circumstances without leaving noticeable traces.
- Add the accompanying information: Where the legislation so requires, add the notified body identification number, the indication of the guaranteed sound power level under 2000/14/EC, and the manufacturer’s details.
- Check before placing on the market: Verify that the marking has been affixed before the product is placed on the market.
The legislation does not specify the method by which the marking is applied. In practice, methods such as metal or plastic data plates, laser marking, engraving or embossing, direct printing and permanent labels are used. Whichever method is chosen, the marking must remain legible under the intended conditions of use of the product (such as outdoor exposure, oil, cleaning and abrasion). For the CE marking process as a whole, see our article on how CE marking is carried out.
When Is the Notified Body Identification Number Required?
Where the applicable legislation so requires, the four-digit identification number of the notified body involved in the production control phase follows the CE marking. The number is affixed by the notified body itself or, under its instructions, by the manufacturer or its authorised representative.
- As a general rule, where the notified body is involved only in the design phase (Module B – type-examination), its identification number does not follow the CE marking (Blue Guide). However, each piece of legislation sets its own rule; see the table below.
- Where a product is subject, under different legislation, to assessment by more than one notified body in the production phase, all of the identification numbers are shown.
- In procedures in which no notified body is involved (for example internal production control – Module A), no number is placed next to the CE marking.
| Legislation | What accompanies the CE marking? |
|---|---|
| 2006/42/EC (machinery) | The identification number of the notified body, where the full quality assurance procedure has been applied (Annex III). |
| (EU) 2023/1230 (from 20 January 2027) | The identification number in procedures involving a notified body: EU type-examination + conformity to type based on internal production control (Module B + C), full quality assurance (Module H) and unit verification (Module G) (Article 24). |
| 2014/30/EU (EMC) | The Directive does not provide for an identification number; a notified body is involved only in EU type-examination (Annex III). |
| 2000/14/EC (noise) | The indication of the guaranteed sound power level (Article 11, Annex IV). The name and address of the notified body involved are stated in the EC declaration of conformity (Annex II). |
Notified bodies and their identification numbers are published in the European Commission’s NANDO database. The identification number of TESTPLUS is 2908.
Additional Rules in the Machinery, Noise and EMC Legislation
In addition to the general CE marking rules, product legislation sets its own requirements. The additional rules in the three areas in which TESTPLUS acts as a notified body are as follows:
Machinery: 2006/42/EC and (EU) 2023/1230
- The components of the CE marking must have substantially the same vertical dimension, which may not be less than 5 mm; the minimum dimension may be waived for small-scale machinery (Annex III).
- The marking is affixed in the immediate vicinity of the name of the manufacturer or its authorised representative, using the same technique (Annex III).
- The machinery must also bear, visibly, legibly and indelibly, the business name and full address of the manufacturer, the designation of the machinery, the designation of series or type, the serial number (if any) and the year of construction (Annex I, 1.7.3).
- It is prohibited to pre-date or post-date the machinery when affixing the CE marking (Annex I, 1.7.3).
- Under the Machinery Regulation (EU) 2023/1230, which applies from 20 January 2027, the marking is affixed visibly, legibly and indelibly to the machinery or related product before it is placed on the market or put into service; where that is not possible, it is affixed to the packaging and to the accompanying documents (Article 24).

For conformity assessment procedures for machinery, see our machinery CE certification page.
Outdoor Equipment: 2000/14/EC
- The CE marking is accompanied by the indication of the guaranteed sound power level; both are affixed visibly, legibly and indelibly to each item of equipment (Article 11).
- The components of the CE marking must have substantially the same vertical dimension, which may not be less than 5 mm (Annex IV).
- The indication consists of the single number of the guaranteed sound power level in dB, the sign LWA and a pictogram. If it is reduced or enlarged, the proportions must be respected; its vertical dimension should, if possible, not be less than 40 mm (Annex IV).
- Markings or inscriptions that are likely to be misleading as to the meaning of the CE marking or of the indication may not be affixed to the equipment (Article 11).
For the equipment covered and the procedures, see our noise emission (2000/14/EC) page and our article on Directive 2000/14/EC.
Electrical and Electronic Apparatus: 2014/30/EU (EMC)
- The CE marking is affixed visibly, legibly and indelibly to the apparatus or to its data plate; where that is not possible or not warranted on account of the nature of the apparatus, it is affixed to the packaging and to the accompanying documents (Article 17).
- The marking is affixed before the apparatus is placed on the market (Article 17).
- As the Directive does not prescribe a specific size, the general rule applies: at least 5 mm.
- The apparatus must also bear a type, batch or serial number and the manufacturer’s name, registered trade name or registered trade mark and postal address; where that is not possible, the information is provided on the packaging or in a document accompanying the apparatus (Article 7).
For conformity assessment under the EMC Directive, see our electromagnetic compatibility (2014/30/EU) page.
Common CE Marking Mistakes
In practice, the most common mistakes regarding CE marking rules and CE marking dimensions are:
- Using a “CE” with narrowed letter spacing or distorted proportions.
- Applying the marking at a height of less than 5 mm.
- Placing the marking only on the packaging or in the instruction manual when it could be affixed to the product.
- Using a label that is easily removed, erased or faded.
- Affixing the marking before conformity assessment has been completed.
- Affixing the marking to a product for which CE marking is not provided for.
- Adding a notified body identification number where it is not required or where the relevant procedure has not been applied.
- On machinery, affixing the marking away from the manufacturer’s name or using a different technique.
- Omitting the indication of the guaranteed sound power level on equipment covered by 2000/14/EC.
Is There a “China Export” Mark?
It is a common misconception that a “CE” with the letters set close together stands for “China Export”. In its answer to European Parliament question P-5938/2007, the European Commission stated that it was not aware of the existence of any such mark and that the mark in question is the CE marking applied without respecting the prescribed dimensions and proportions. A “CE” with distorted proportions is therefore not a separate mark but an improperly affixed CE marking.
Consequences of an Improperly Affixed CE Marking
Failure to comply with the CE marking rules is a non-compliance. Under the formal non-compliance provisions of EU product legislation, the competent authority first requires the non-compliance to be remedied; if it persists, the authority may restrict or prohibit the product being made available on the market, or ensure that it is recalled or withdrawn from the market.
In Türkiye, those who act contrary to the “CE” Marking Regulation are subject to Law No 7223 on Product Safety and Technical Regulations (Article 15). Regulation (EC) No 765/2008 also requires Member States to take action against improper use of the marking and to provide for penalties, which may include criminal sanctions for serious infringements (Article 30).
Frequently Asked Questions
What is the minimum size of the CE marking?
Unless the applicable legislation specifies a different value, the minimum CE marking size is a height of 5 mm. With the proportions respected, a marking 5 mm high has a total width of 7 mm.
Is there a maximum size for the CE marking?
No. The legislation sets no upper limit; the marking may be enlarged to suit the size of the product, provided the proportions of the scale drawing are respected.
Where can I get the CE marking dimensions?
The CE marking dimensions are given in the scale drawing in Annex II of Regulation (EC) No 765/2008. The calculator and generator on this page provides the marking at the size you enter as SVG, DXF and PNG. The European Commission also publishes vector files of the marking on its CE marking page; the marking must be scaled without distorting its proportions.
What colour should the CE marking be?
The legislation does not prescribe a specific colour. According to the European Commission’s Blue Guide, the marking may take different forms (for example a different colour, solid or hollow) as long as it remains visible and legible and its proportions are respected.
Can the CE marking be placed only on the packaging or in the instruction manual?
Only where the nature of the product does not allow the marking to be affixed to the product or its data plate, or where its permanence cannot be ensured. In that case, the marking is affixed to the packaging and to the accompanying documents required by the applicable legislation. Aesthetic reasons alone are not sufficient.
Can the CE marking be applied as a label?
Yes. The marking does not have to form an integral part of the product; it may be affixed by means of a data plate or a permanent label. However, it must be indelible, meaning that it cannot be removed under normal circumstances without leaving noticeable traces.
Can an importer affix the CE marking?
The CE marking is affixed only by the manufacturer or its authorised representative. An importer who places a product on the market under its own name or trademark, or who modifies a product already on the market in a way that may affect its conformity, is considered a manufacturer and assumes the manufacturer’s obligations. Otherwise, the importer verifies that the manufacturer has affixed the marking and drawn up the required documents.
Is it mandatory to put a notified body number next to the CE marking?
Not always. The identification number is added only where the applicable legislation so provides and the notified body was involved in that procedure. In procedures in which no notified body is involved (for example internal production control), no number is placed next to the CE marking.
Is the CE marking affixed to partly completed machinery?
Not under the machinery legislation. Partly completed machinery does not bear the CE marking; it is accompanied by a declaration of incorporation and assembly instructions instead of an EC declaration of conformity. If the product also falls within the scope of other legislation that provides for CE marking, it is marked in accordance with that legislation.
Can a product without the CE marking be placed on the market?
A product covered by legislation that provides for CE marking may not be placed on the market without the marking. Conversely, affixing the CE marking to products outside the scope of such legislation is prohibited.
Is the CE marking a quality or origin mark?
No. According to the European Commission, the CE marking does not indicate that a product has been approved as safe by the EU or by another authority, nor does it indicate the origin of the product. The marking is the manufacturer’s declaration that the product meets the requirements of the applicable legislation.
Can the CE marking be used together with other markings?
Yes. Other markings may be affixed to the product provided that the visibility, legibility and meaning of the CE marking are not impaired. Markings, signs and inscriptions that are likely to mislead as to the meaning or form of the CE marking are prohibited.
Does a “CE” with the letters close together mean “China Export”?
No. The European Commission has stated that it is not aware of the existence of any mark called “China Export”. A “CE” with distorted proportions is not a separate mark; it is the CE marking applied without respecting its dimensions and proportions.
Conformity Assessment with TESTPLUS
Affixing the CE marking and drawing up the EU declaration of conformity are the responsibility of the manufacturer. As EU Notified Body NB 2908, TESTPLUS carries out conformity assessment under 2000/14/EC noise emission, 2006/42/EC machinery safety and 2014/30/EU electromagnetic compatibility.
The CE marking rules and CE marking dimensions summarised in this article are for general information; for the requirements applicable to a specific product, the current text of the applicable legislation prevails.
Sources: Regulation (EC) No 765/2008 (Article 30, Annex II) · “CE” Marking Regulation of Türkiye (Official Gazette 27.05.2021 / 31493, in Turkish) · Blue Guide 2022 (2022/C 247/01) · European Commission CE marking page