Skip to main content

Connected machinery now falls under two overlapping sets of EU cybersecurity rules. The Machinery Regulation (EU) 2023/1230 treats cyber threats as a machine safety issue, and the Cyber Resilience Act (CRA), Regulation (EU) 2024/2847, sets horizontal cybersecurity requirements for products with digital elements. This article explains how the two fit together and which dates matter for machine builders.

Does the CRA Apply to Machinery?

Factory control room with industrial network and automation infrastructure

The CRA applies to products with digital elements whose intended or reasonably foreseeable use includes a direct or indirect data connection to a device or network. A machine with a networked PLC, HMI, remote maintenance gateway or connected drive falls within that description, as do the software and control components supplied separately for it. A purely stand-alone machine with no data connection is the main case outside scope.

Key Dates

Date What applies
10 December 2024 CRA entered into force
11 September 2026 CRA reporting obligations for actively exploited vulnerabilities and severe incidents
20 January 2027 Machinery Regulation (EU) 2023/1230 applies
11 December 2027 CRA applies in full to products placed on the market

What the Machinery Regulation Requires

Annex III of the Machinery Regulation contains two requirements directly related to cybersecurity:

  • Section 1.1.9, protection against corruption: Connection to another device or a remote link must not lead to a hazardous situation. Hardware and software that are critical for compliance must be identified and protected against accidental or intentional corruption, and the machine must collect evidence of legitimate or illegitimate intervention.
  • Section 1.2.1, safety and reliability of control systems: Control systems must withstand reasonably foreseeable malicious attempts by third parties that could lead to a hazardous situation.

The focus is safety: the manufacturer’s risk assessment must consider cyber threats that can defeat or alter safety functions.

What the CRA Adds

  • Essential cybersecurity requirements: Products must be designed, developed and produced to an appropriate level of cybersecurity based on a documented cybersecurity risk assessment, and placed on the market without known exploitable vulnerabilities.
  • Vulnerability handling: Manufacturers must identify and document components, including a software bill of materials, address vulnerabilities without delay and provide security updates.
  • Support period: Vulnerabilities must be handled for a support period that reflects the expected time in use, at least five years unless the product is expected to be in use for less.
  • Reporting: Actively exploited vulnerabilities and severe incidents must be reported through the single reporting platform, with an early warning within 24 hours and a fuller notification within 72 hours.
  • Documentation and marking: Technical documentation, an EU declaration of conformity and CE marking cover CRA compliance alongside other applicable legislation.

How the Two Regulations Fit Together

Aspect Machinery Regulation Cyber Resilience Act
Objective Health and safety of persons Cybersecurity of the product throughout its life cycle
Trigger Machinery and related products Products with digital elements and a data connection
Core analysis Risk assessment including cyber threats to safety functions Cybersecurity risk assessment
After placing on the market No general update duty Vulnerability handling and security updates during the support period

A connected machine placed on the market after 11 December 2027 must satisfy both. The Machinery Regulation also provides that machinery certified under a relevant European cybersecurity certification scheme benefits from a presumption of conformity with sections 1.1.9 and 1.2.1, as far as the certificate covers those requirements.

Conformity Assessment Under the CRA

Most products with digital elements can be assessed by the manufacturer under internal control. Products listed in the CRA as important or critical follow stricter routes, which can require a notified body designated under the CRA. Machine builders should check whether components they place on the market separately, such as industrial firewalls, routers or certain control products, fall into those classes.

What Machine Builders Should Do Now

Secure update of machine control software
  1. List every digital and connected element of each machine type, including third-party controllers and software.
  2. Extend the machinery risk assessment to cover cyber threats to safety functions.
  3. Start a cybersecurity risk assessment and a software bill of materials for each product.
  4. Set up a process for receiving, assessing and reporting vulnerabilities; the reporting obligations already apply.
  5. Define the support period and how security updates will be delivered.
  6. Request cybersecurity information and CRA commitments from component suppliers.

TESTPLUS (NB 2908) carries out conformity assessment for machinery. For background, see our article on the Machinery Regulation (EU) 2023/1230 and our Machine CE Certificate page.

Related reading